Huzhou Automatic Terminal Machine Processing Factory

The ultra-high-speed silent peeling and tapping machine in the workshop is a fixed asset. The use date is March 2012, and the life span is 10 years. Its original value is 18,000 yuan. It is a general enterprise production equipment. /span>Strip terminal machineThe straight-line method is used to accrue depreciation, and the monthly depreciation amount=18000*(1- 3%)/10/12=145.50. The use date is from March 2012 to July 2013, which is 9+7=16 months, and the depreciation amount in July 2013=145.5*16=2328 yuan.

Dongguan Julun Machinery Co., Ltd. is engaged in the manufacture and sales of domestic terminal machines, computer stripping machines, wire and cable processing equipment 2113. Wire harness connector processing equipment and various connectors. .Service as a professional enterprise. The company has a large number of professional and technical personnel, a strong after-sales service system and advanced precision processing equipment. Its electrical and mechanical accessories are imported from Taiwan 5261 and Japan, combined with advanced technical experience in Europe, America and Taiwan , Continue to develop, innovate, and provide customers with 4102 high-quality, high-efficiency products and services

Excessive pressure on the stripping terminal machine or other problems, check and debug to OK. Before operation, check each locking screw and confirm that there is no looseness inside. WhenFully automatic terminal machineThe blades of will experience a certain degree of At this time, the riveted terminals may have defective products. The cutting blades of the equipment will have certain hidden dangers after 1 million or even 2 million cuttings. Therefore, it is used by high-demand customers. In the process, if the service life of wearing parts needs to be strictly controlled, the correct operation of the equipment can also reduce the loss.

Continuous stripping terminal machine: The continuous stripping terminal machine belongs to the semi-active model. It has the function of active peeling and crimping terminals. After manual feeding, the foot pedal power switch is controlled to complete the operation. The output power is relatively high. The machine has the functions of active peeling and crimping. During the operation, manual feeding is required, and the pedal method is required, and the production power is high. The quotation is cheaper than the quotation of all active terminal machines.

Poor peeling of the stripper and terminal machine: the peeling time varies. There are many reasons for different stripping lengths. The common stripping length is too tight or too loose. At this time, it is only necessary to properly adjust the open space between the two wheels until the wire cannot be pulled by hand. On the other hand, this may be a problem with the blade. The blade is cut too deep or too shallow, and even the blade is installed at an angle, which may also cause this result. At this time, it is necessary to adjust the position of the blades as needed. If it is caused by damage to the blade, it is recommended to replace the blade immediately. Inconsistent cutting lengths Inconsistent cutting lengths may be due to blade or blade wear; to encounter such a problem, simply replace the cutter with a new one.

How to install domestic terminal machine and automatic terminal machine? ①Put the qualified terminals on the terminal frame as required, and install the terminal chain head into the equipment according to the correct method. ②Confirm that the die of the equipment matches the installed terminal, then adjust the pressure and other parameters of the equipment, and adjust the corresponding position of the terminal chain and the equipment. ③Take the stripped wire and check for defects, then align the wire with the slot of the terminal machine and the terminal opening, adjust the position, and then step on the pedal with your foot to place the terminal on the wire.

Huzhou Automatic Terminal Machine Processing Factory

The stripper and terminal machine must be shut down when adjusting and replacing the paper cutter. Even when the machine is stopped, it is strictly forbidden to put your hands under the knife to change the knife. Long-handled bolts and other tools should be used to change the knife. They must be removed during the test run to avoid injury to the operator when the machine is started. 2. The power supply must be blocked when the stripping terminal machine is adjusted, the blade is exchanged, and when repairing, refueling, scrubbing and inspection.

湖州自動端子機加工廠

Check whether the power supply voltage of the stripper terminal machine is consistent with the specified voltage (220V). Fix the terminal roll and guide the terminal into the die through the guide plate. Adjust the crimping height and manually operate the pressure test terminal. After turning the spindle into place with an open-end wrench, remove the open-end wrench. 2. Manual operation of Dongguan Julun automatic terminal machine: Turn the operation switch to the adjustment position (POWEROFF) and the motor will not run at this time. Insert the open-end wrench into the spindle from the rear box door, and press the manual button (ADJUST) solenoid to attract it. The open-end wrench rotates clockwise to drive the main shaft to rotate one round, the main machine slide block moves up and down to complete a stroke, and a terminal is crimped. Keep pressing the manual button (ADJUST) to turn it in place continuously, and then remove the open-end wrench.

Turn on the power switch of the automatic terminal, and the power indicator light is on. Pay attention to whether there are obvious abnormal noises inside and outside the machine. If the operation is suspended, ask the maintenance personnel to determine whether maintenance is required. Knife selection and installation: operated by designated personnel. Before installing the tool, you need to manually compare whether the selected tool matches. The tool can only be installed after the comparison is correct. After installing the tool, it must be tested manually.

The development of domestic terminal machine: how to install the automatic terminal machine? Put the qualified terminals on the domestic terminal rack according to the requirements, and install the terminal chain head into the equipment according to the correct method. Confirm that the die of the equipment matches the installed terminal, then adjust the pressure and other parameters of the equipment, and adjust the corresponding position of the terminal chain and the equipment. Take the stripped wire and check for defects, then align the wire with the slot of the terminal machine and put it in the terminal opening, adjust the position, and then step on the pedal with your foot.

Introduction to the working principle of the domestic terminal machine: The terminal machine is a machine used for wire processing, which can press the hardware head to the end of the wire. Then do conduction. The terminal produced by the terminal machine is usually for more convenient connection, and the two wires can be connected together stably without welding. And only need to unplug the power plug when disassembling. What is the working principle of the domestic terminal machine? 1. (Stepping principle) The motor keeps rotating. There is a circuit breaker in the clutch, and each action is a standard "O", which is very common. 2. In the past five years, there was a (silent) terminal with a server. Its working principle is different from the above. It just sends a message to the server and then transmits it to the motor to perform the operation.

Huzhou Automatic Terminal Machine Processing Factory

First, turn off the power of the automatic terminal machine, press the down touch button, and use the special board to manually move the master and slave wheels to greatly increase the original imported terminal pressure The punching stroke of the machine. If the hand does not move, consider whether the pressure is too high or there are other problems, check and adjust to normal. Before operation, check and confirm that the locking screws are not loose.

Huzhou Automatic Terminal Machine Processing Factory

一、全自動端子機運轉前的準備：(1)檢查國產壓著機和壓模安裝是否穩固，腳踏開關和電源插座是否插牢。(2)檢查電源電壓是否與規定電壓(220V)相符。(3)固定端子卷，將端子經導料板引到壓模內。(4)調整壓著高度，手動操作試壓端子。(5)用開口扳手將主軸扳到位后，取下開口扳手二、鉅綸全自動端子機手動操作。

湖州自動端子機加工廠

After processing a line at Huzhou Automatic Terminal Machine Processing Factory, affix a sticker on the rubber plate, and be sure to indicate the type of stripping terminal machine used for the line, The specification and quantity of the wire. For the processing of the same kind of wire, the Huzhou automatic terminal machine processing plant shall re-check after the equipment has been continuously operated for 1 hour to make sure that the wire stripping machine and the length of the wire stripping and the wire opening effect are qualified. If you are qualified, you can continue production. You can try the domestic terminal machine operation method of Julun Machinery. Introduction to the five installation steps of the automatic terminal machine.