Weifang terminal machine manufacturer

Put a sticker on the plastic basin and indicate the line usedStripping terminal machineModel, line specifications and quantity. In addition, for the same kind of wire processing, after the stripping terminal machine is continuously operated for 1 hour, it is necessary to re-check to confirm the length of the wire and the length of the wire and whether the wire effect is qualified, and then continue production after confirming that it is qualified. Ensure the quality of each batch of the stripping terminal machine.

JulunFully automatic terminal machineClosing height (Pressing height) adjustment: When the closing height of the stripping terminal machine is not suitable or the adjustment of the mold pressing height micro-adjuster plate is not enough, it can be realized by adjusting the adjustment joint and loosening the round nut. Insert the adjusting rod into the round hole on the adjusting joint and turn it. Turning left will decrease the pressing height, and turning right will increase the pressing height (the engraved line on the adjusting joint is 0.1mm per grid, and one turn is 3mm). From high to low, adjust to the proper compression of the wires and terminals. It should not be too tight. Too tight will easily damage the upper and lower die blades.

This type of supply terminal machine is equipped with a foot-operated ionization 2113 switch, because when the terminal machine is running, its motor is constantly running, and every time it is stepped on The pedal will give an "O" power off signal. This is a type of our common terminal 5261 machine. The supply terminal machine can also be called a terminal crimping machine or a terminal crimping machine. As companies move towards automated production, the terminal machine market in recent years has been occupied by the 4102 automatic terminal machine for most of the market.

Ultra-quiet terminal machine: using modern inverter control skills, the terminal machine with the server (inverter), similar to the working principle of the stripping machine, but does not have Active stripping function (usually used in cooperation with a computer stripping machine), suitable for crimping of various terminals and wires. Digital control, safety maintenance system, and simple operation complete the accuracy, strength and safety beyond the reach of machinery. Make the terminal The machine runs ultra-quietly,

Applying the inner cavity shape can make the blank obtain the corresponding three-dimensional shape. The mold generally includes two parts: a movable mold and a fixed mold (or a convex mold and a concave mold), which can be separated or combined. The parts are taken out when they are separated, and the blanks are injected into the mold cavity to form when they are closed. The stripping terminal machine mold is a precision tool with a complex shape that can withstand the expansion force of the blank. It has high requirements for structural strength, rigidity, surface hardness, surface roughness and processing accuracy. The development level of mold production is at the level of mechanical manufacturing. One of the important signs.

Full-automatic parallel wire terminal machine. (It adopts PLC or single-chip control, servo motor or stepper motor to provide power. The production process does not require manual participation, and the production efficiency is high. This type of domestic equipment can realize about 7000pcs of wire cutting per hour and 11000pcs of terminal crimping. The mid-term is 3500pcs. Parallel wire crimping terminal, 7500pcs is a single wire crimping terminal, which can automatically detect the crimping quality of the terminal. It has the functions of the above three automatic terminal machines. It is currently one of the most highly automated terminal machines in the domestic market)

So the key point is that too tight will crush the copper wire or directly break the blade. If it is loose, the terminals and wires will easily fall off. You should do more , I think you will be familiar with this one. If you still don’t understand during the operation, you can call: 0769-87883409 Dongguan Julun Machinery Co., Ltd. We are a professional manufacturer of original imported terminal machines and wire stripping machines. Will let you know how to debug the terminal machine

Supplied terminal machine harness processing equipment nationwide to make fully automatic terminal crimping machines. Terminal machine. Wire cutting machine. Cassette mode. The blade waits for someone to do better. Dongguan Julun Machinery Co., Ltd. is committed to the research, development, manufacturing and sales of automatic wire processing machinery and equipment. The product range includes full-automatic single-head terminal machine, full-automatic double-head terminal machine, continuous stripping and tapping machine,Ultra-quiet terminal machine, computer wire stripping machine, high-speed wire cutting machine, pipe cutting machine, tying machine, etc. Products are exported to Southeast Asia, Europe and the United States. Sincerely welcome new and old customers to come to discuss cooperation.

Safety inspection of Dongguan Julun automatic terminal machine before operation: confirm that the wrench has been removed. Tighten the round nut after adjustment. Press the operating switch of the stripper terminal machine to the working position, and the motor starts to run. Place the wire in the proper position of the crimping part of the terminal (the crimped terminal must be in the middle of the upper and lower die cutters). Step on the foot switch, the main unit slides down, complete the crimping of the wire and the terminal, and send the next terminal to the crimping position. Repeat the above steps to achieve continuous crimping between the wire and the terminal.

Weifang terminal machine manufacturer

The inverter itself can save electricity by 30%, plus the ultra-quiet terminal machine is energized once during operation, avoiding unnecessary idling of the motor and saving electricity when used. No noise, with low operating noise, high function, and low quotation.

The stripping and tapping machine is a semi-automatic type. As the name suggests, it has the functions of automatic peeling and crimping of the terminals, but it requires manual feeding and manual control of the foot power switch to work. The production efficiency is high and the price is low. 3. The ultra-quiet terminal machine and the supply terminal machine with the server (frequency converter) belong to the semi-automatic model, which requires manual feeding and manual control of the pedal power switch to work. The working principle is similar to the stripping terminal machine, but it does not have the automatic thinning function (usually used in conjunction with the computer wire cutting machine), low energy consumption and low price.

The safety of supplying terminal machines: Talking about the functional advantages of supplying automatic terminal machines. The functional advantages of supplying automatic terminal machines are introduced as follows: The supply of automatic terminal machines refers to wire processing requirements The machine used, also known as the fully automatic stripping and end pressing machine, is a new type of equipment that has just been released in recent years. It is a multifunctional machine integrating feeding, cutting, stripping and end pressing. It is humane and intelligent. The high-end technology products are suitable for large, medium and small enterprises, saving labor. Increase work efficiency.

The stripper and terminal machine will operate the switch to the adjustment position (POWEROFF) and the motor will not run. Insert the open-end wrench into the spindle from the rear box door, and press the manual button ○2 (ADJUST) solenoid to attract it. The open-end wrench rotates clockwise to drive the main shaft of the stripper and terminal machine to rotate one circle, the main slider of the stripper and terminal machine moves up and down to complete a stroke, and one terminal is crimped. The manual button, kept pressed, can be turned into place continuously, and then remove the open-end wrench. To proceed.

Weifang terminal machine manufacturer

Excessive pressure on the stripping terminal machine or other problems, check and debug to OK. Before operation, check each locking screw and confirm that there is no looseness inside. When the blade of the automatic terminal machine has undergone 200,000 times of stamping, there will be a certain degree of wear. At this time, the riveted terminal may have defective products. The cutting blade of the equipment has experienced 1 million or even 2 million times. After the cutting and stripping, there will be certain hidden dangers. Therefore, in the use process of high-demand customers, it is necessary to strictly control the service life of the wearing parts, and the correct operation of the equipment can also reduce the loss.